®

VALENCIA 600 II LVC
HOUSING
Cylindrical post top luminaire consists of base with shade supported by four stainless steel support rods. Heavy-duty cast aluminum base with integral slip fitter anchors the support rods, and is machined to include groove for gasketing and mounting surface for the lens and driver enclosure. Shade shall be spun aluminum and free from burrs and sharp edges. Shade and base are gasketed to provide a weather-tight seal to the clear acrylic cylindrical lens. Luminaire slip fits 3" O.D. pole or tenon, and has built-in stop to limit insertion depth to 3". Two offset rows of three 10mm recessed setscrews secure the luminaire to the pole. All hardware is stainless steel.

OPTICS
LED light engine consists of a vertically oriented optical quality acrylic rod capped with a reflective element to redirect light outward. The acrylic rod channels light from the single CoB LED and redirects it outward to provide effective horizontal and vertical illumination. Light shaping diffusing film on the inside of the main luminaire lens controls and shapes light distribution for optimal performance while minimizing brightness. Thermal management is provided via heat sinking and convective cooling within the sealed system.

ELECTRICAL
Electrical components are mounted in a white conical enclosure at the base of the luminaire. Electronic LED driver supplies 700mA drive current to the LED. The driver has a universal input voltage range from 120v to 277v at 50/60Hz. Driver is high power factor with performance greater than 90%. Power consumption is 24 watts. Optional 0-10v dimming available on request.

LED DELIVERED LUMENS / BUG RATING (Pending final photometric test results)
Module 360
3000K: 3750 lumens / B1-U4-G3
4000K: 4125 lumens / B2-U4-G3

NOTE: Due to rapid and continuous advances in LED technology, LED luminaire data is subject to change without notice and at the discretion of HessAmerica. Consult factory for current technical data.

POLE
Stepped steel pole is manufactured from cold drawn seamless mechanical tubing with nominal wall thickness of 0.126". Flush mounted hand hole cover is plasma cut with kerf not to exceed 1/8" and includes triangular tamper-resistant locking device. Pole is hot-dip galvanized with coating inside and out, then lightly sanded prior to painting. Base cover is one-piece 0.080" spun aluminum and finished to match the pole. Specify 8' or 10' nominal pole heights with 3' step or 12' nominal pole height with 4' step. Stepped aluminum pole is manufactured from extruded 6061-T6 aluminum alloy. Upper shaft is 3" OD with 0.125" wall thickness. Lower shaft is 4.5" OD with 0.237" wall thickness. Machined aluminum transition is plug- and circumferentially welded to both shafts. Flush mounted hand hole cover is plasma cut with kerf not to exceed 1/8" and includes triangular tamper-resistant locking device.

Twin mount bracket assembly is fabricated from steel, then hot-dip galvanized. Slip fitter has inner steel sleeve which functions as a stop to limit insertion depth to 6.7". Assembly slip fits 3" O.D. pole and is secured with two rows of four 10mm stainless steel setscrews. Twin pairs of parallel square steel tubing are welded to connect the slip fitter to the individual tenons for fixture mounting. Bracket assembly ships pre-wired with fish tape.

Single and twin 24" banner arm assemblies available upon request. Banner arm assemblies consist of upper fixed arm and lower breakaway arm for high-wind conditions. Stainless steel lanyard inside lower arm safely retains the arm in event of breakaway.

FINISH
Housing is cleaned ultrasonically prior to painting. Standard Primar™ finish is finely textured matte silver metallic, dark grey, graphite grey, black, or dark bronze. Special RAL colors available on request.

INGRESS PROTECTION: IP54

CERTIFICATION
CSA/US Certified for Wet Locations

WARRANTY
Limited product warranty period including the LEDs is five years. Driver shall carry the respective manufacturer's limited warranty.