CAMPONE
CAMPONE captures tasteful European styling with design simplicity and graceful form. The slender conical luminaire with acrylic lens tapers down to match the tenon base with a subtle reveal at the transition. Cast aluminum housing with integral fitter secures to the wall bracket with regressed setscrews. The facetted reflector is formed from high-reflectance pre-anodized aluminum with a textured micro-surface to efficiently distribute light and minimize brightness. Available distributions include symmetric and asymmetric light patterns. A decorative fascia surrounding the reflector is perforated stainless steel. Luminaire and bracket are finished in finely texture paint. All hardware is stainless steel.
Specification
CAMPONE 810 LVC
HOUSING
Luminaire housing with integral fitter is cast aluminum. Four vertical rods fastened to the housing support the optical system and act as a wire way to provide power to the LED circuit board. Conical lens is clear acrylic and sealed with one-piece silicone gaskets to provide a weather tight seal when closed. Roof is spun aluminum. A stainless steel thumbscrew secures the roof, allowing tool-less access to the luminaire. Luminaire mounts to tenon on pole and secured with two offset rows of three regressed setscrews. Luminaire slip fits over 3" OD tenon with insertion depth of 4.2". All hardware is stainless steel.
OPTICS
Optical assembly consists of one LEVO C LED module mounted within the cylindrical clear acrylic lens. The module consists of an aluminum core PCB with four high-power LEDs and a single piece lens molded from optical quality acrylic. Light distributions include a choice of Type II, III, IV, or V optics. LED circuit boards are equipped with electrical disconnects to allow for future technology upgrades. CRI is 80+.
ELECTRICAL
Electronic LED driver supplies 700mA drive current to the LED module with input voltage range from 120v through 277v at 50/60Hz. Power consumption is 37 watts. Optional 0-10v DC dimming is available on request.
DELIVERED LUMEN OUTPUT / BUG RATING
3000K
Type 2 = 3248 lumens / B1-U1-G1
Type 3 = 3356 lumens / B1-U2-G1
Type 4 = 3261 lumens / B1-U1-G1
Type 5 = 3542 lumens / B2-U1-G1
4000K
Type 2 = 3456 lumens / B1-U1-G1
Type 3 = 3571 lumens / B1-U2-G1
Type 4 = 3469 lumens / B1-U1-G1
Type 5 = 3768 lumens / B2-U1-G1
NOTE : Due to rapid and continuous advances in LED technology, LED luminaire data is subject to change without notice and at the discretion of HessAmerica. Consult factory for current technical data.
LUMINAIRE WEIGHT: 25 lbs
LUMINAIRE EPA: 2.3 sq ft
MOUNTING
Fabricated steel mounting bracket mounts over junction box and is secured to wall in four places.
FINISH
Standard finishes are finely textured matte silver grey metallic, dark grey, graphite grey, matte black, or dark bronze. Special colors available on request.
INGRESS PROTECTION: IP65
CERTIFICATION
CSA/US Certified for Wet Locations
WARRANTY
Limited product warranty period including LEDs is five years. Driver shall carry the manufacturer's limited warranty.
Luminaire housing with integral fitter is cast aluminum. Four vertical rods fastened to the housing support the optical system and act as a wire way to provide power to the LED circuit board. Conical lens is clear acrylic and sealed with one-piece silicone gaskets to provide a weather tight seal when closed. Roof is spun aluminum. A stainless steel thumbscrew secures the roof, allowing tool-less access to the luminaire. Luminaire mounts to tenon on pole and secured with two offset rows of three regressed setscrews. Luminaire slip fits over 3" OD tenon with insertion depth of 4.2". All hardware is stainless steel.
OPTICS
Optical assembly consists of one LEVO C LED module mounted within the cylindrical clear acrylic lens. The module consists of an aluminum core PCB with four high-power LEDs and a single piece lens molded from optical quality acrylic. Light distributions include a choice of Type II, III, IV, or V optics. LED circuit boards are equipped with electrical disconnects to allow for future technology upgrades. CRI is 80+.
ELECTRICAL
Electronic LED driver supplies 700mA drive current to the LED module with input voltage range from 120v through 277v at 50/60Hz. Power consumption is 37 watts. Optional 0-10v DC dimming is available on request.
DELIVERED LUMEN OUTPUT / BUG RATING
3000K
Type 2 = 3248 lumens / B1-U1-G1
Type 3 = 3356 lumens / B1-U2-G1
Type 4 = 3261 lumens / B1-U1-G1
Type 5 = 3542 lumens / B2-U1-G1
4000K
Type 2 = 3456 lumens / B1-U1-G1
Type 3 = 3571 lumens / B1-U2-G1
Type 4 = 3469 lumens / B1-U1-G1
Type 5 = 3768 lumens / B2-U1-G1
NOTE : Due to rapid and continuous advances in LED technology, LED luminaire data is subject to change without notice and at the discretion of HessAmerica. Consult factory for current technical data.
LUMINAIRE WEIGHT: 25 lbs
LUMINAIRE EPA: 2.3 sq ft
MOUNTING
Fabricated steel mounting bracket mounts over junction box and is secured to wall in four places.
FINISH
Standard finishes are finely textured matte silver grey metallic, dark grey, graphite grey, matte black, or dark bronze. Special colors available on request.
INGRESS PROTECTION: IP65
CERTIFICATION
CSA/US Certified for Wet Locations
WARRANTY
Limited product warranty period including LEDs is five years. Driver shall carry the manufacturer's limited warranty.
Documents
Catalogue page | Hessamerica_CAMPONE.pdf (PDF, 587.07 KB) |
Drawings | campone_wall_usa.png (PNG, 3.68 KB) |
Product brief |
IES / Image
Photometric reports | CP810-T2-NW.ies (BIN, 62.68 KB) CP810-T2-WW.ies (BIN, 62.68 KB) CP810-T3-NW.ies (BIN, 32.08 KB) CP810-T3-WW.ies (BIN, 32.08 KB) CP810-T4-NW.ies (BIN, 31.89 KB) CP810-T4-WW.ies (BIN, 31.89 KB) CP810-T5-NW.ies (BIN, 16.51 KB) CP810-T5-WW.ies (BIN, 16.52 KB) |
Mounting detail |
hessamerica_mounting_details_template_CP810_wall.png (PNG, 43.25 KB) |
Product images | CAMPONE.zip |